There is an Edge Detection Switch (in blue) on Edge-Alignment Photo Sensor on Fabric Inspection Machine, operator could use screwdriver to adjust the switch, rotating the switch to more right, the sensitivity will be higher.

The hand wheel could adjust the speed difference of two pulleys. The two pulleys are connected with the twin rewinding rollers separately. If there is speed difference between the two pulleys, there is also speed difference between the two rewinding rollers which could result in tight or loose fabric rolls. In this respect, the hand wheel could control the roll tightness through different speed. S...

One set Edge Alignment Photo Sensor is installed at one side of fabric edge on Fabric Inspection Machine to detect whether it is deflective. When the sensor detected the edge is not aligned, the Rewinding Station will move left or right to make the edge aligned.

The principle of cutting is “pressure”, not the “sharpness” of the cutter. We suggest you to adjust the position of sealing cutter by regulating all screws (in below red), to make sure the cutter is in the horizontal plane, so that the cutter is with uniform force.

We have teflon tape in random accessories,if the damage is not serious,you can make a simple repair with teflon tape.if serious,you need buy a new sealing cutter

Three sets of Scroll Roller and One set of Air-blowing device to control fabric curled edges.1 Before inspection table, the scroll roller will make fabric open totally when inspection.2 After inspection, the scroll roller will open fabric curled edges again to make sure an accurate edge-align.3 Before rewinding, the scroll roller& Air-blowing device will once more open fabric and eliminate crease ...

1)Please make sure the the new silicone bar is used with new sealing cutter2)The principle of cutting is “pressure”, not the “sharpness” of the cutter. We suggest you to adjust the position of sealing cutter by regulating all screws (in below red), to make sure the cutter is in the horizontal plane, so that the cutter is with uniform force.

1.Blade: Blade must be replaced when it wears 3-4mm. Be sure the front faceof the knife when re-setting the knife. Words market face is the front face.2.Carbon brush: When the motor runs not normally,should cut off the power and check the carbon brush. The carbon brush should be replaced when it wears to 5-6mm.

ST-MBT-09 Motorized Warp Beam Low Lift Trolley,it is used to transport warper's beams and warp beams weighing up to 2500kgs.ST-MBT-11 Motorized A-frame Tractor,it is used to lift and tow batch trolleys A-frames up to 5000kgs.For both ST-MBT-09 and ST-MBT-11 are without PLC.

SUNTECH Warp Beam is applicable for Sulzer, Toyota, Dornier, Tsudakoma, Picanol, Somet, etc.with flange diameter of 600-1250mm. Beam is manufactured with single and twin section accompanied with driving gear for smooth working.Customized beam working width or other special requirement can be satisfied.Material:Beam Tube: seamless steelBeam Flange: Aluminium ZL104 Alloy + other alimuniums

How to figure up the width of PE film needed according to the width?FABRIC WIDTH = ROLL WIDTH + ROLL DIAMETER + 15cm

Yes, we have upgraded the Fabric Folding Machine to be suitable for mesh net fabric.1.We add one Motor at the fabric feeding position, which could feed fabric automatically without stretching.2. Adding Electrical Tension Control, we will make sure the speed of fabric feeding, checking and rewinding are synchronized. The dancing roller is specially designed for tension control. The dancing roller w...

Generally, the free spare parts of ST-ASCM Automatic Fabric Sample Cutting Machine are 02pcs Cutting Mats, 01 pc Working Wrench, 01 pc Straight /Zig-zag Cutting Blade, 01 Oil Bottle. Please kindly note, the oil bottle is empty because of the shipping rule, the oil is prohibited.

The charging time of battery is normally 8 hours,we suggest evenly charge once a month.The new machine must be charged 12 hours first 3 times.Do not follow the principle of operation, the battery life is vulnerable to damage.Battery application:continuous working condition is 4-6 hours,intermittent working is 8 hours.Battery life: scrapped after charge and discharge 700 times.

For the ST-LTM-01 Loom Take-up Machine with inspection function, there is a touch screen on the machine.For the ST-LTM-01 Loom Take-up Machine without inspection function,there is no touch screen on the machine.Advantages: easy operation, you can set up parameters,adjust speed and tension.

For FCL, steel pallet + stretch film coveringFor LCL, steel frame + wooden box packing

SUNTECH is a professional manufacturer with experience over 40 years. Now we have brand office in HK and International sales office in Hangzhou(Hangzhou Strength MachineryCo.,Ltd). Your order will be controlled from very beginning to the last.

There are two dancing rollers in the inspection machine:the one near the inlet position is to synthesize the unwinding and inspection speed;the one under the inspection table is to synthesize the inspection and rewinding speed.The solution is:1. see below marked drawing, to adjust the counter weights to the right;2. if the problem still there when the counter weights adjust to the right-most side,...

For Heavy Fabric: the counter weight has be moved away from the dancing bars, or to add more counter weights.For Lighter Fabric: the counter weight has to be moved closer to the dancing bars, or to reduce counter weights.

Welcome to visit the Accessories website: http://suntech-machine.en.........../

Yes, Suntech has it own International Office to sale the weaving accessories.Welcome to visit the website at: http://suntech-machine.en.........../

According to the principle of PLC system, it's possible to cut 10*10mm.But in practice,10mm is so small that will lead to the fabric deviate its normal location,then it won't be so accurate to 10*10mm.According to our experience,the min swatch size 25mm is the best.

The machine will contain three light boxes free of charge (within range of 18-50").You could choose the light box size per your real demand.The box is suitable for fabric width up or down one inch. For example, 30inch light box can check fabric width of 29-31inch.In this way, you could combine the light boxes, to meet your fabric width range largely.E.g. One of our customer will use the tubular fa...

There are many different size fabric samples, so how to make fabric samples with Fabric Sample Cutting Machine?Suntech has three kinds of Fabric Sample Cutting Machine, one is Hand type Fabric Sample Cutter, one is Motorized Fabric Cutting Machinethe other is Fully Automatic Fabric Sample Making Machine.The cutting length, cutting size, cutting height, cutting effect are adjustable, different size...

Suntech ST-LTM Loom Take-up Machine has two models, with inspection function and without inspection function. We could produce the machine as per customer's requirements.Thanks for our Russia customer-LLC TAVRIA taken the photos for us, the machine is with inspection function.

Yes, Suntech Fabric Inspection Machine is with PLC System, if the customer do not want the PLC System, it's available in Suntech. Except the following types machine, which with Centre Driven System.If there is no PLC, the rewinding and unwinding will be not smooth, the centre driven system will be damaged quickly.So if you want the Centre Driven System at feeding position, we suggest the machine ...

PLC of ST-BS Beam Stacker can connect with SAP system of our customer to achieve function,which can monitor the storage information of beams. We need to change the PLC and touch screen.ItemCurrent ModelNew ModelPLCJAPANESE OMRON(CP1L-L14DR-D)JAPANESE OMRON( CP1L-M40DR)Touching ScreenTAIWANESE WEINVIEW(TK6070)TAIWANESE WEINVIEW(MT8071iE)

ST-LTM Batcher Machine is used to attach all type of weaving machines. For most heavy rolls, there are options for choice-Pneumatic Roll Ejection Device (in below red) or Manual Doffing Motion.

The dancing roller in Fabric Inspection Machine is used to adjust the fabric tension.Heavy Fabric: the counter weight has be moved away from the dancing bars, or to add more counter weights.Lighter Fabric: the counter weight has to be moved closer to the dancing bars, or to reduce counter weights. Dancing Roller Working Principle:When the speed is different, the potentionmeter in the dancing rolle...

The machine will contain three light boxes free of charge (within range of 18-50").You could choose the light box size per your real demand.The box is suitable for fabric width up or down one inch. For example, 30inch light box can check fabric width of 29-31inch.In this way, you could combine the light boxes, to meet your fabric width range largely.E.g. One of our customer will use the tubular fa...

The Automatic Fabric Roll Packing Machine is upgraded - with the function of smart classification.Operator can setup the assignations in PLC system.Fabric roll from inspection machine no.1 can be assigned to storage stage no.1 (or no.2 or no.3 or no.4).Fabric roll from inspection machine no.2 can be assigned to storage stage no.2 (or no.1 or no.3 or no.4).Fabric roll from inspection machine no.3 c...

1. TAKE OFF ALL THE FABRIC FROM FOLDING MACHINE. 2. CHECK THE CLOTH GUIDERS, MAKE SURE THEY ARE SYMMETRICAL. 3. HOW TO SOLVE THE ‘’CREASE’’ ISSUE:THE KEY FACTOR OF ‘’CREASE’’ ISSUE IS THE HEIGHT OF TRIANGLE FRAME.AND PLEASE ADJUST THE TRIANGLE FRAME TO A HIGHER POSITION BY BELOW TWO PARTS: NOTE: PLEASE ADJUST THE TRIANGLE FRAME HEIGHT TO A HIGHER POSITION SIGHTLY, AND OPERATOR NEED TO ADJUST THE...

ST-ARPM Automatic Fabric Roll Packing MachineAutomatic Fabric Roll Packing Machine is used to pack fabric rolls for vacuum effect.How can the machine pack fabric roll in order?The whole process is controlled by PLC and adjusted by photo-sensor.1.No auto storage conveyor: if the speed of packing can catch up with the speed of rolling,there is no need to add storage stage. Several Inlet Conveyor + P...

The operator can adjust the roll tightness by adjusting the hand wheel. The hand wheel on the fabric inspection machine is used for adjusting the speed difference of two pulleys. The two pulleys are connected with the twin rewinding rollers separately. If there is speed difference between the two pulleys, there is also speed difference between the two rewinding rollers, and so result in tight or l...

Heavy Fabric: the counter weight has be moved away from the dancing bars, or to add more counter weights.Lighter Fabric: the counter weight has to be moved closer to the dancing bars, or to reduce counter weights.

SUNTECH ST-MSCM Motorized Fabric Sample Cutting Machine is used for cutting square fabric samples with zigzag or flat edges.And there is a laser around the cutting blade on ST-MSCM for better measurement to improve the cutting performance.

Yes, Suntech could dispatch the engineer overseas for machine installation, maintenance and training.Our after-sell service principle is to solve any machine quality problem no matter how much it would cost us as long as the machine is within warranty, and to provide lifetime service to make customer feel absolutely guaranteed.But if the problem is not caused by us, the customer need to bear the a...

LTM-01 Loom Take-up MachineLTM-02 Loom Take-up MachineLTM-01 Loom Take-up MachineLTM-02 Loom Take-up MachineRewinding Speed0-1.15m0-10mDiameter1500mm1000mmLTM-02 has a roller accumulator installed.The roller accumulator will store the fabric from the loom,make the speed synchronized with rewinding and control the tension. So the rewinding speed can be ajusted faster than the loom.

The 2 models of Suntech ST-TFSM-01 and ST-TFSM-02 are both for slitting open tubular fabrics:And the differences between standard ST-TFSM-01 and ST-TFSM-02 are:1) Automatic Level: ST-TFSM-01--Fully Automatic, ST-TFSM-02--Semi Automatic;2) Suitable Fabric Type: ST-TFSM-01--Wet, Semi-Wet and Dry Fabrics, ST-TFSM-02--Dry Fabrics;3) Inlet Form: ST-TFSM-01--Plaited Fabrics, ST-TFSM-02--Roll of Tubular ...

Yes, Suntech starts its new weaving accessories business in August, 2016. Customers could find the many accessories in Suntech, like weaver beam, warp beam, heald wire and drop wire.