Search This Supplers Products:fabric inspection machinefabric rolling machinefabric folding machinefabric cutting machinewarp beam trolleybeam stacker
How does the weighing device convert "kg" to "pounds"? 1) Keep pressing "Function Button" until it shows "P1-1". 2) Press "Tare Button" to change the number to "2".3) Press "# Button" to finish this process. ...
timeMon, 03 Jun 2019 17:50:45 GMT
ST-WFIM length from Wheel type Encoder to Rewinder roller(L1) can not be ...
timeFri, 24 May 2019 14:50:19 GMT
Can you provide fully automatic fabric end cutter? We do not provide fully automatic fabric end cutter, and we normally only recommend customers to use the semi-automatic cutter, because the fully automatic cutter may cause harm to operator when sometimes the cu...
timeThu, 09 May 2019 16:05:10 GMT
If you just have 2 sets of inspection machine, we don't recommend it, because the function just can used to record the general information and defect types, locations & serious degree. If you have 5 sets, 10 sets or more sets of inspection machine, this system also can connect together to be as a i...
timeMon, 06 May 2019 16:08:59 GMT
How to operate the 4-point system? 1)Install the software into the computer and connected the computer with the machine2)You need identify 24 defects onto the software in the computer and the computer will record some general information you input like date, or...
timeThu, 25 Apr 2019 14:25:47 GMT
What is 4-point System? Faults Recording System/Software adopts America 4-point Standard, which could record 24 defects (customized), these defects could be given penalty from 1-4 serious degree on operation panel. The more serious of defects, the more penalty ...
timeMon, 22 Apr 2019 13:31:54 GMT
Does the machine have a guard or shut off switch or sensor ?(ST-WFIM) 1-There is a shut off switch on operation panel (in below red), in case someone puts their hand near the rollers, press the button, the machine will stop running. 2-Normally, the rolling speed...
timeThu, 18 Apr 2019 15:04:38 GMT
How to adjust the rewinding roll tightness(ST-WFIM )? The hand wheel could adjust the speed difference of two pulleys. The two pulleys are connected with the twin rewinding rollers separately. If there is speed difference between the two pulleys, there is also s...
timeMon, 15 Apr 2019 13:29:21 GMT
How much fabric is it needed to wind the machine? Q:The rolls I work with are of 50 yds(45.7m), and I am seeing that the process to wind the rolls is a very long process and it requires a lot of fabric. How much fabric is it needed to wind the machine? Because I...
timeThu, 11 Apr 2019 15:58:35 GMT
How to adjust the sensitivity of edge-alignment photo sensor? This i...
timeWed, 10 Apr 2019 11:04:44 GMT
3.How does this machine control the edge-alignment? One set of Edge-alignment Photo Sensor which is installed at one side of fabric edge to detect whether it is deflective . When the sensor detected the edge is not aligned, the Rewinding Station will move left o...
timeTue, 09 Apr 2019 10:37:36 GMT
Woven Fabric inspection Machine Normally for model ST-WFIM-320, its most suitable fabric width is 1600-3200mm.Because if the fabric width is too narrow on a wider working width machine , the roller will be deformed after long time using. Therefore, we would like...
timeThu, 04 Apr 2019 13:47:05 GMT
Put the fabric in the center of the machine and the cloth guider on the both sides of fabric.Please make sure each cloth guider has the same distance to its each correspondent beam. The cloth guider will avoid fabric deviation, to place fabric in machine center. ...
timeWed, 03 Apr 2019 11:00:36 GMT
Regarding this machine, we use Japanese imported alloy cutting blade,which is three times durable than normal cutting blade. And we have sold lots of this machine,all the feedbacks from our current customers are positive. So we are confident about our quality. If there is any questions occurred within warranty time, we will be fully responsible and send you free spares immediately. It just takes 3...
timeFri, 09 Feb 2018 11:17:58 GMT
1)Install the software into the computer and connected the computer with the machine2)You need identify 24 defects onto the software in the computer and the computer will record some general information you input like date, order, shift, operator's name, in the copmputer3)When the operator found defects when inspecting, manully stop the machine, select defects and give penalty from 1-4 serious deg...
timeFri, 29 Dec 2017 14:40:47 GMT
1. Battery charging time is generally 8 hours, we suggest equalizing charge once a month. For new machine, it must be charged 12 hours for first three times. The using life of the battery will be harmed if not operated by principle.2. The use of battery: It could be used 4 to 6 hours under continuous use condition; It could be used 8 hours under discontinuous use condition.3. Using life: It is not...
timeFri, 22 Dec 2017 11:26:20 GMT
It is because there is no inlet conveyor, operator would send the fabric roll to main packing unit directly by hand. The fabric roll had not finished width sealing,when operator put another roll into packing machine, so the machine didn’t detect the coming fabric roll and fail packing.Besides, if the fabric roll is not feed straightly onto the conveyor which also disturbs the detection of the ...
timeThu, 14 Dec 2017 11:16:32 GMT
After using the machine, please turn off the power and use the cotton cloth to wiping the sealing cutters when the cutter still have the heat. Also you can paint Teflon on the surface of the cutters. If it’s still not workable, we suggest you to buy a new cutter.
timeWed, 25 Oct 2017 16:51:52 GMT
All the small guide roller are flexiable instead of fixed rollers; all the big diameter roller are motor driven, more helpful for fabric delivery and tension control. Only when the fabric is stretched tightly, the stocking is easily snaging. When you watch the video, you will find the fabric is rel...
timeTue, 17 Oct 2017 18:38:25 GMT
Heavy Fabric: the counter weight has be moved away from the dancing bars, or to add more counter weights.Lighter Fabric: the counter weight has to be moved closer to the dancing bars, or to reduce counter weights.Knitted Fabric Inspection Machine: http://..........com/pid17903525/SUNTECH-Fabric-Inspection-for-knitted-fabric-with-tension-control.htm
timeThu, 12 Oct 2017 16:49:03 GMT
Our length measurement error is less than 0.1m/km. There are two sets of wheels work together Wheel type encoder and Nylon wheel work together to ensure the accurate measurement. Wheel Type Encoder under the Inspection Table--to measure the length. The lighter Nylon Wheel on the Inspection Table--to ensure the below Wheel Type Encoder can touch the fabric for measuring. On the meanwhile...
timeMon, 09 Oct 2017 10:53:12 GMT
Three sets of Scroll Roller and One set of Air-blowing device to control fabric curled edges. 1 Before inspection table, the scroll roller will make fabric open totally when inspection. 2 After inspection, the scroll roller will open fabric curled edges again to make sure an accurate edge-align. 3 Before rewinding, the scroll roller& Air-blowing device will once more open fabric and elimi...
timeFri, 22 Sep 2017 17:28:09 GMT
Mechanical Tension Control:60 degree fixed angle inspection screen, which has been verified thousand times to prove to be the most suitable angle for knitted fabric. It has the least influence for fabric tension.Electrical Tension Control: Make sure the speed of fabric feeding, checking, rewinding are synchronized. The dancing roller will move up and down to control the fabric tension. Suppose the...
timeFri, 15 Sep 2017 17:32:08 GMT
Yes, We can use PE-film thicker than 60-80 microns, (for example 120mm) but if so, we will need to specially customize the packing machine's sealing cutter, and the cutter will only be suitable for that thickness. Normally we would recommend customer to use the PE film in thickness 60-80 micros, because it is not only suitable for the our standard sealing cutter, but also its thickness is ...
timeThu, 07 Sep 2017 17:09:53 GMT
The Lifter can be added after packing, it can rise the fabric roll to the exact height then push it to the stalliage for collection directly. The height can be customized by customers requirements, and its price will be vary.Fabric Roll Packing Machine: http://..........com/pid17183055/SUNTECH-Fabric-Roll-Packing-Machine.htm
timeThu, 31 Aug 2017 17:43:09 GMT
First of all, I have to say it is fabric roll packing machine, it has no crease eliminate function. You need to make sure there is no crease on your fabric roll before packing. Then please kindly check below information one by one: 1) Please kindly check the PE film, whether it is correct and in good quality; thickness 60-80 Microns; 2 ) Please kindly check if the sealing cutter temperature is...
timeThu, 24 Aug 2017 17:25:43 GMT
What is the appropriate sealing cutter temperature?Normally it is around 125-130℃,but it could be adjusted as per the actual situation.What is the appropriate heat chamber temperature?Normally it is around 180-200℃, but it could be adjusted as per the actual situation.
timeThu, 17 Aug 2017 17:27:28 GMT
Polythene PE film, Thickness 60-80 Microns. Two different kinds of polythene film for the two packing proposals.1).Normal Packing Proposal: Normal PE film, thickness 60-80 microns, without heat shrinking function 2) Vacuum Packing Proposal: Heat-shrinking PE film, thickness 60-80 microns for vacuum packing. The heat-shrinking film should be able to continuously working ten seconds under 180-20...
timeThu, 10 Aug 2017 16:44:03 GMT
It is because there is no inlet conveyor, operator would send the fabric roll to main packing unit directly by hand. The fabric roll had not finished width sealing,when operator put another roll into packing machine, so the machine didn’t detect the coming fabric roll and fail packing. Besides, if the fabric roll is not feed straightly onto the conveyor which also disturbs the detection of th...
timeWed, 02 Aug 2017 17:07:27 GMT
Here is steps for you to follow before operatinga.Pls check the centering roller at the feeding place. Its function is avoiding fabric deviation.b.Adjust the triangle frame to make the fabric at center position.c.Pls adjust the the edge-alignment raster on the limited bar and install on a correct position where it can detect the fabric edge. When operating, the edge-alignment raster can move left ...
timeWed, 26 Apr 2017 19:29:02 GMT
Our machine design is passive unwinding by roll cradle.Testified by the industry and according to the customer's feedback, It has very very little influence on fabric tension. So customers no need to worry about tension. The rewinding form of our machine is by twin motor-driven rollers which is surface contacting with fabric for rewinding. Perfect controlling in fabric tension.
timeWed, 26 Apr 2017 19:22:09 GMT
We will provide three different sizes of light boxes according to customers requirements for various fabric , but the range is 18-50inch. 30inch light box can check fabric of 29-31inch width. 3 Light Transmitter controls fabric checking box lighting wireless.
timeWed, 26 Apr 2017 18:25:25 GMT
Normally, our standard ST-ASCM is fully automatic, it's much more convenient and easy to cooperate. But we also could do , the operator need to control the cutting mat by handle.
timeMon, 27 Mar 2017 20:47:23 GMT
Normally the zig-zag pitch is 5mm, we also could do 3mm and 7mm
timeMon, 27 Mar 2017 20:28:52 GMT
1- Take off all the fabric from fabric folding machine.2- Check the cloth guiders, make sure the distance between two side clothe guiders to two side beams is same.3- Set the button of "sensitiveness adjusting" between 6 & 7.4- After finishing above three steps, loading the fabric on fabric folding machine, After fabric folded by triangle frame, the folded fabric will go through the edge-alignment...
timeSun, 12 Mar 2017 20:16:06 GMT
The key factor of "crease" issue is the height of triangle frame. Adjust the triangle frame to a heigher position by adjusting the support rod on Fabric Folding Machine
timeSun, 12 Mar 2017 20:03:36 GMT
First of all, before fabric inspection machine running, the fabric will be feeded by hand, and the fabric length from Wheel type Encoder to Rewinder roller(L1) can not be measured, because at this time, the digital counter meter does not start to count. After machine start, the operator will cut the fabric roll by Linear Fabric Cutter, the fabric length from Wheel type Encoder to Rewinder roller(...
timeFri, 03 Mar 2017 19:08:56 GMT
There is a shut off switch on operation panel (in below red), in case someone puts their hand near the rollers, press the button, the machine will stop running. Normally, the rolling speed is 15m/min, this speed is safe enough, and there is a enough gap between two rewinding rollers, in case someone puts their hand into the rollers,the hand will not be rolled and hurted because of the safety speed...
timeFri, 03 Mar 2017 19:05:47 GMT
Faults Recording System/Software on Fabric Inspection Machine adopts America 4-point Standard, which could record 24 defects (customized), these defects could be given penalty from 1-4 serious degree on operation panel. The more serious of defects, the more penalty will be given.
timeFri, 24 Feb 2017 19:01:44 GMT
The switch of the Edge-Alignment is on operation panel of fabric inspection machine and folding machine.
timeFri, 24 Feb 2017 18:59:42 GMT
网络文化经营许可证:浙网文[2013]0268-027号|增值电信业务经营许可证:浙B2-20080224-1 2007-2025 Tradevv.com. All rights reserved.