How does the weighing device convert "kg" to "pounds"? 1) Keep pressing "Function Button" until it shows "P1-1". 2) Press "Tare Button" to change the number to "2".3) Press "# Button" to finish this process. ...

ST-WFIM length from Wheel type Encoder to Rewinder roller(L1) can not be ...

Can you provide fully automatic fabric end cutter? We do not provide fully automatic fabric end cutter, and we normally only recommend customers to use the semi-automatic cutter, because the fully automatic cutter may cause harm to operator when sometimes the cu...

If you just have 2 sets of inspection machine, we don't recommend it, because the function just can used to record the general information and defect types, locations & serious degree. If you have 5 sets, 10 sets or more sets of inspection machine, this system also can connect together to be as a i...

How to operate the 4-point system? 1)Install the software into the computer and connected the computer with the machine2)You need identify 24 defects onto the software in the computer and the computer will record some general information you input like date, or...

What is 4-point System? Faults Recording System/Software adopts America 4-point Standard, which could record 24 defects (customized), these defects could be given penalty from 1-4 serious degree on operation panel. The more serious of defects, the more penalty ...

Does the machine have a guard or shut off switch or sensor ?(ST-WFIM) 1-There is a shut off switch on operation panel (in below red), in case someone puts their hand near the rollers, press the button, the machine will stop running. 2-Normally, the rolling speed...

How to adjust the rewinding roll tightness(ST-WFIM )? The hand wheel could adjust the speed difference of two pulleys. The two pulleys are connected with the twin rewinding rollers separately. If there is speed difference between the two pulleys, there is also s...

How much fabric is it needed to wind the machine? Q：The rolls I work with are of 50 yds（45.7m）, and I am seeing that the process to wind the rolls is a very long process and it requires a lot of fabric. How much fabric is it needed to wind the machine? Because I...

How to adjust the sensitivity of edge-alignment photo sensor? This i...

3.How does this machine control the edge-alignment? One set of Edge-alignment Photo Sensor which is installed at one side of fabric edge to detect whether it is deflective . When the sensor detected the edge is not aligned, the Rewinding Station will move left o...

Woven Fabric inspection Machine Normally for model ST-WFIM-320, its most suitable fabric width is 1600-3200mm.Because if the fabric width is too narrow on a wider working width machine , the roller will be deformed after long time using. Therefore, we would like...

Put the fabric in the center of the machine and the cloth guider on the both sides of fabric.Please make sure each cloth guider has the same distance to its each correspondent beam. The cloth guider will avoid fabric deviation, to place fabric in machine center. ...

1)Install the software into the computer and connected the computer with the machine2)You need identify 24 defects onto the software in the computer and the computer will record some general information you input like date, order, shift, operator's name, in the copmputer3)When the operator found defects when inspecting, manully stop the machine, select defects and give penalty from 1-4 serious deg...

All the small guide roller are flexiable instead of fixed rollers; all the big diameter roller are motor driven, more helpful for fabric delivery and tension control. Only when the fabric is stretched tightly, the stocking is easily snaging. When you watch the video, you will find the fabric is rel...

Heavy Fabric: the counter weight has be moved away from the dancing bars, or to add more counter weights.Lighter Fabric: the counter weight has to be moved closer to the dancing bars, or to reduce counter weights.Knitted Fabric Inspection Machine: http://..........com/pid17903525/SUNTECH-Fabric-Inspection-for-knitted-fabric-with-tension-control.htm

Our length measurement error is less than 0.1m/km. There are two sets of wheels work together Wheel type encoder and Nylon wheel work together to ensure the accurate measurement. Wheel Type Encoder under the Inspection Table--to measure the length. The lighter Nylon Wheel on the Inspection Table--to ensure the below Wheel Type Encoder can touch the fabric for measuring. On the meanwhile...

Three sets of Scroll Roller and One set of Air-blowing device to control fabric curled edges. 1 Before inspection table, the scroll roller will make fabric open totally when inspection. 2 After inspection, the scroll roller will open fabric curled edges again to make sure an accurate edge-align. 3 Before rewinding, the scroll roller& Air-blowing device will once more open fabric and elimi...

Mechanical Tension Control:60 degree fixed angle inspection screen, which has been verified thousand times to prove to be the most suitable angle for knitted fabric. It has the least influence for fabric tension.Electrical Tension Control: Make sure the speed of fabric feeding, checking, rewinding are synchronized. The dancing roller will move up and down to control the fabric tension. Suppose the...

Our machine design is passive unwinding by roll cradle.Testified by the industry and according to the customer's feedback, It has very very little influence on fabric tension. So customers no need to worry about tension. The rewinding form of our machine is by twin motor-driven rollers which is surface contacting with fabric for rewinding. Perfect controlling in fabric tension.

We will provide three different sizes of light boxes according to customers requirements for various fabric , but the range is 18-50inch. 30inch light box can check fabric of 29-31inch width. 3 Light Transmitter controls fabric checking box lighting wireless.

First of all, before fabric inspection machine running, the fabric will be feeded by hand, and the fabric length from Wheel type Encoder to Rewinder roller(L1) can not be measured, because at this time, the digital counter meter does not start to count. After machine start, the operator will cut the fabric roll by Linear Fabric Cutter, the fabric length from Wheel type Encoder to Rewinder roller(...

There is a shut off switch on operation panel (in below red), in case someone puts their hand near the rollers, press the button, the machine will stop running. Normally, the rolling speed is 15m/min, this speed is safe enough, and there is a enough gap between two rewinding rollers, in case someone puts their hand into the rollers,the hand will not be rolled and hurted because of the safety speed...

Faults Recording System/Software on Fabric Inspection Machine adopts America 4-point Standard, which could record 24 defects (customized), these defects could be given penalty from 1-4 serious degree on operation panel. The more serious of defects, the more penalty will be given.

The switch of the Edge-Alignment is on operation panel of fabric inspection machine and folding machine.

There is an Edge Detection Switch (in blue) on Edge-Alignment Photo Sensor on Fabric Inspection Machine, operator could use screwdriver to adjust the switch, rotating the switch to more right, the sensitivity will be higher.

The hand wheel could adjust the speed difference of two pulleys. The two pulleys are connected with the twin rewinding rollers separately. If there is speed difference between the two pulleys, there is also speed difference between the two rewinding rollers which could result in tight or loose fabric rolls. In this respect, the hand wheel could control the roll tightness through different speed. S...

One set Edge Alignment Photo Sensor is installed at one side of fabric edge on Fabric Inspection Machine to detect whether it is deflective. When the sensor detected the edge is not aligned, the Rewinding Station will move left or right to make the edge aligned.

Three sets of Scroll Roller and One set of Air-blowing device to control fabric curled edges.1 Before inspection table, the scroll roller will make fabric open totally when inspection.2 After inspection, the scroll roller will open fabric curled edges again to make sure an accurate edge-align.3 Before rewinding, the scroll roller& Air-blowing device will once more open fabric and eliminate crease ...

There are two dancing rollers in the inspection machine:the one near the inlet position is to synthesize the unwinding and inspection speed;the one under the inspection table is to synthesize the inspection and rewinding speed.The solution is:1. see below marked drawing, to adjust the counter weights to the right;2. if the problem still there when the counter weights adjust to the right-most side,...

For Heavy Fabric: the counter weight has be moved away from the dancing bars, or to add more counter weights.For Lighter Fabric: the counter weight has to be moved closer to the dancing bars, or to reduce counter weights.

The machine will contain three light boxes free of charge (within range of 18-50").You could choose the light box size per your real demand.The box is suitable for fabric width up or down one inch. For example, 30inch light box can check fabric width of 29-31inch.In this way, you could combine the light boxes, to meet your fabric width range largely.E.g. One of our customer will use the tubular fa...

Yes, Suntech Fabric Inspection Machine is with PLC System, if the customer do not want the PLC System, it's available in Suntech. Except the following types machine, which with Centre Driven System.If there is no PLC, the rewinding and unwinding will be not smooth, the centre driven system will be damaged quickly.So if you want the Centre Driven System at feeding position, we suggest the machine ...

The dancing roller in Fabric Inspection Machine is used to adjust the fabric tension.Heavy Fabric: the counter weight has be moved away from the dancing bars, or to add more counter weights.Lighter Fabric: the counter weight has to be moved closer to the dancing bars, or to reduce counter weights. Dancing Roller Working Principle:When the speed is different, the potentionmeter in the dancing rolle...

The machine will contain three light boxes free of charge (within range of 18-50").You could choose the light box size per your real demand.The box is suitable for fabric width up or down one inch. For example, 30inch light box can check fabric width of 29-31inch.In this way, you could combine the light boxes, to meet your fabric width range largely.E.g. One of our customer will use the tubular fa...

The operator can adjust the roll tightness by adjusting the hand wheel. The hand wheel on the fabric inspection machine is used for adjusting the speed difference of two pulleys. The two pulleys are connected with the twin rewinding rollers separately. If there is speed difference between the two pulleys, there is also speed difference between the two rewinding rollers, and so result in tight or l...

Heavy Fabric: the counter weight has be moved away from the dancing bars, or to add more counter weights.Lighter Fabric: the counter weight has to be moved closer to the dancing bars, or to reduce counter weights.

Difference between Simple Fabric Inspection Machine and Table-type Inspection MachineST-TIMST-SFIMFabric type and widthhometextilewidth≤1.8mfabric without elasticity and curled edgefabric width≥1.8m Feeding positionwithout cloth guiderwith cloth guiderLightingbottom lighttop and bottom lightsInspection screentable type30 degree fixed angle screen

Fabric Inspection Machine:1. Mechanical Tension Control:- 60 degree fixed angle inspection screen, which has been verified thousand times to prove to be the most suitable angle for knitted fabric. It has the least influence for fabric tension.2. Electrical Tension Control:- The dancing roller will move up and down to control the fabric tension. It make sure the speed of fabric feeding, checking, r...

The whole process of winding the fabric on the machine is around 3.5m, and it is just around1.5m below the inspection screen, which can not be inspected. For inspecting every roll, we recommend to add a fabric end stop sensor at feeding posion, when it detects there is no coming fabric, the machine will stop automatically to let the operater join the next roll. In this way, there will be no fabric...